Skip to content Skip to footer

CirKit Boss Auxiliary Fuse Block/7 Circuits/Weatherproof (7 Ignition 12V) Part No 70217

$110.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70217 Category: Tags: , , , , , , Product ID: 21259

Description

The safe way to add electrical accessories to any vehicle is with a CirKit Boss®™; The first circuit isolator system available with both constant and ignition hot circuit kits.  Kits include an in-line circuit breaker, relay, relay/fuse block base with a pre-terminated harness, and mounting hardware and terminals.  Protects your OEM warranty and is easy to install.

70217– Provides seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

This kit includes:

  • Two weatherproof 40 Amp SPST relays
  • Two weatherproof 40 Amp circuit breakers
  • Weatherproof relay bases/fuse blocks with harness
  • Weatherproof crimp-on heat-shrinkable terminals
  • Weatherproof fuse block cover
  • Mounting hardware

You may also like…

CirKit Boss Auxiliary Fuse Block/3 Circuits/Weatherproof (3 Ignition 12V) Part No 70213

$83.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70213 Category: Tags: , , , , , Product ID: 21257

Description

The safe way to add electrical accessories to any vehicle is with a CirKit Boss®™; The first circuit isolator system available with both constant and ignition hot circuit kits.  Kits include an in-line circuit breaker, relay, relay/fuse block base with a pre-terminated harness, and mounting hardware and terminals.  Protects your OEM warranty and is easy to install.

70213– Provides three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

This kit includes:

  • One weatherproof 40 Amp SPST relay
  • One weatherproof 40 Amp circuit breaker
  • Weatherproof relay base/fuse block with harness
  • Weatherproof heat-shrinkable crimp-on terminals
  • Weatherproof fuse block cover
  • Mounting hardware

You may also like…

CirKit Boss Heavy Duty Auxiliary Fuse Block/7 Circuits (7 Ignition 12V) Part No 70118

$144.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70118 Category: Tags: , , , , , Product ID: 21247

Description

The safe way to add electrical accessories is with a CirKit Boss®™ kit from Painless Performance.  This kit allows for the addition of 7 fused circuits to your already existing factory fuse block.  Simply mount the fuse block and relays, route the large 6 gauge wire to the battery, route the ignition wire, and then route the 7 accessory circuits to the accessories needing power.  The main power wire is 8 feet long from the fuse block.  Each accessory circuit has 8 feet of wire length from the fuse block.

70118– 7 ignition hot circuits switched through two 70 Amp relays.

This kit includes:

  • Two 70 Amp SPST relays
  • Two Relay bases/fuse block with harness
  • Crimp-on terminals
  • Mounting hardware

You may also like…

CirKit Boss Auxiliary Fuse Block/7 Circuits (7 Ignition 12V) Part No 70117

$96.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70117 Category: Tags: , , , , , Product ID: 21245

Description

The safe way to add electrical accessories to any vehicle is with a CirKit Boss®™; the first circuit isolator system available with both constant and ignition hot circuit kits.  Kits include an in-line circuit breaker, relay, relay/fuse block base with a pre-terminated harness, and mounting hardware and terminals.  Protects your OEM warranty and is easy to install.

70117– Provides seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

This kit includes:

  • Two 40 Amp SPST relays
  • Two 40 Amp circuit breakers
  • Relay bases/fuse blocks with harness
  • Crimp-on terminals
  • Mounting hardware

CirKit Boss Heavy Duty Auxiliary Fuse Block/3 Circuits (3 Ignition 12V) Part No 70114

$90.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70114 Category: Tags: , , , , , Product ID: 21243

Description

The safe way to add electrical accessories is with a CirKit Boss®™ kit from Painless Performance.  This kit allows for the addition of 3 fused circuits to your already existing factory fuse block.  Simply mount the fuse block and relay, route the large 10 gauge wire to the battery, route the ignition wire, and then route the 3 accessory circuits to the accessories needing power.  The main power wire is 8 feet long from the fuse block.  Each accessory circuit has 8 feet of wire length from the fuse block.

70114- Provides three ignition hot circuits with a maximum total Amperage handling of 70 Amps. This kit includes:

  • One 70 Amp SPST relay
  • Relay base/fuse block with harness
  • Crimp-on terminals
  • Mounting hardware

You may also like…

CirKit Boss Auxiliary Fuse Block/3 Circuits (3 Ignition 12V) Part No 70113

$67.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70113 Category: Tags: , , , , , , Product ID: 21241

Description

The safe way to add electrical accessories to any vehicle is with a CirKit Boss®™; the first circuit isolator system available with both constant and ignition hot circuit kits.  Kits include an in-line circuit breaker, relay, relay/fuse block base with a pre-terminated harness, and mounting hardware and terminals.  Protects your OEM warranty and is easy to install.

70113 Provides three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

This kit includes:

  • One 40 Amp SPST relay
  • One 40 Amp circuit breaker
  • Relay base/fuse block with harness
  • Crimp-on terminals
  • Mounting hardware

You may also like…

CirKit Boss Auxiliary Fuse Block/7 Circuits (3 Constant 12V – 4 Ignition 12V) Part No 70107

$80.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70107 Category: Tags: , , , , , , , Product ID: 21239

Description

The safe way to add electrical accessories to any vehicle is with a CirKit Boss®™; the first circuit isolator system available with both constant and ignition hot circuit kits.  Kits include an in-line circuit breaker, relay, relay/fuse block base with a pre-terminated harness, and mounting hardware and terminals.  Protects your OEM warranty and is easy to install.

70107– Provides three 20 Amp constant hot and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

This kit includes:

  • One 40 Amp SPST relay
  • One 50 Amp circuit breaker
  • Relay base/fuse block with harness
  • Crimp-on terminals
  • Mounting hardware

You may also like…

CirKit Boss Auxiliary Fuse Block/3 Circuits (1 Constant 12V – 2 Ignition 12V) Part No 70103

$67.99

Other three circuit CirKit Boss®™ kits available:

70113 – Three ignition-hot circuits with a maximum total amperage handling of 40 Amps.

70103 – Non-weatherproof version of 70203.

70203– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

70213 – Weatherproof version of 70113.

Need more circuits?  Check out these seven circuit versions of our CirKit Boss®™ kits.

70107 – Three 20 Amp constant hot circuits and four ignition hot circuits with a maximum total amperage handling of 40 Amps.

70117 – Seven ignition hot circuits with a maximum total amperage handling of 80 Amps.

70207 – Weatherproof version of 70107.

70217 – Weatherproof version of 70117.

Need some serious Amperage handling?  Check out these heavy duty CirKit Boss®™ kits.

70114 – Three ignition hot circuits with a maximum total Amperage handling of 70 Amps.

70118 – Seven ignition hot circuits with a maximum total Amperage handling of 140 Amps.

70120 – Replacement rubber cover for fuse block.

Painless Part Number: 70103 Category: Tags: , , , , , Product ID: 21237

Description

The safe way to add electrical accessories to any vehicle is with a CirKit Boss®™; the first circuit isolator system available with both constant and ignition hot circuit kits.  Kits include an in-line circuit breaker, relay, relay/fuse block base with a pre-terminated harness, and mounting hardware and terminals.  Protects your OEM warranty and is easy to install.

70103– Provides one 30 Amp constant hot and two 20 Amp ignition hot circuits.

This kit includes:

  • One 40 Amp SPST relay
  • One 50 Amp circuit breaker
  • Relay base/fuse block with harness
  • Crimp-on terminals
  • Mounting hardware

You may also like…

Trail Rocker – 4 Switch Panel – Flange / Under Dash Mount Part No 57109

$169.99

Painless Part Number: 57109 Category: Tags: , , , , Product ID: 21092

Description

The Painless Trail Rocker Switch Panels are as rugged as any trail you’ll encounter. The weatherproof LED On/Off switches are enclosed in a powder-coated steel housing. Available in a 4, 6, or 8 switch option, with mounting options available for dash mount, roll bar mount (1⅝” and 1¾”), or flanged under dash mount. Designed to be plug-n-play with the Painless Trail Rocker systems and includes optional winch wiring. Includes everything required to install and mount.

Dimensions: 6″ x 3½” x 2″ (width, height, depth).

You may also like…

Trail Rocker – 8 Switch Panel – Flange / Under Dash Mount Part No 57103

$229.99

Painless Part Number: 57103 Category: Tags: , , , , Product ID: 21082

Description

The Painless Trail Rocker Switch Panels are as rugged as any trail you’ll encounter. The weatherproof LED On/Off switches are enclosed in a powder-coated steel housing. Available in a 4, 6, or 8 switch option, with mounting options available for dash mount, roll bar mount (1⅝” and 1¾”), or flanged under dash mount. Designed to be plug-n-play with the Painless Trail Rocker systems and includes optional winch wiring. Includes everything required to install and mount.

Dimensions: 11″ x 3½” x 2″ (width, height, depth).

You may also like…

6 Switch Extreme Off-Road Switch Panel w/ Push Button Part No 50341

$209.99

Engine: Any
Trans.: Any

Number of Circuits:  7 CIRCUITS
Harness Length: No Wires Included
Fuse Type: No Fuses Included
Firewall Passthrough: (1) Grommet & (3) Caps Included – Depending on side of box wires are routed to.
Color Code Based:  Painless Specific
Circuit Designations:  7 Circuit System – 6 Outputs Selectable By Customer

Connections Included:

Ignition, Start, 1 thru 6 Individual Toggle Switch Outputs with Indicator Lights Toggle Switches Included: (5) On/Off, (2) On/Off/On, (2) Momentary On

Painless Part Number: 50341 Category: Tags: , , Product ID: 21031

Description

Panel Dimensions: 10.75″ L x 2.5″ W x 3″ H

The 6 Switch Extreme Off-Road Switch Panel w/ Push Button is BY FAR THE BEST designed OFF-ROAD SWITCH PANEL to handle the harshest conditions an Off-Road Vehicle can be exposed to. This Switch Panel includes a matching box to allow mounting to a roll cage. It features a formed polyethylene liner to seal off all of the rear connections on the individual toggle switches AND the Ignition or Push Button Starter Switches. This same polyethylene liner also acts like a gasket between the switch panel face plate to the switch panel box; creating a highly water-resistant seal. THIS MEANS you can wash the mud, dirt, and grim off of your OFF-ROAD RIG with the garden hose without worrying about ruining your electrical system.

The Push Button Switch used in this kit includes a robust rubber-sealed outer nut to help protect the switch from the elements.

The Toggle Switches are all rated at 20 Amps and are protected from the elements by the included weather-resistant boots that thread onto the outside of each switch.

THIS Switch Panel DOES NOT include any wires. It is designed to work DIRECTLY with the TWO Chassis Harnesses; listed below, depending on if the vehicle is needing to be STREET LEGAL or OFF-ROAD ONLY. Both harnesses have Accessory Circuits that can be controlled by the Toggle Switches in the Panel.

10144 – 15 Circuit Weatherproof Extreme Off-Road Harness (OFF-ROAD ONLY)

OR

10140 – 26 Circuit Weatherproof Off Road Chassis Harness (STREET LEGAL) & (OFF-ROAD)

 

Peel and Stick Labels are included to identify what each output is connected to and covers most applications.

Painless also offers 4  & 6 Toggle & Ignition Switch Panel(s) WITH THE WIRING: 

50330 – 4 Toggle & Ignition Switch, Off-Road Switch Panel, Dash Mount

50332 – 6 Toggle & Ignition Switch, Off-Road Switch Panel, Dash Mount

Or if you prefer a 4 or 6 Toggle & Push Button Start Switch Panel:

50335 – 4 Toggle, Push Button Start Switch, Off-Road Switch Panel, Roll Bar Mount

50336 – 6 Toggle, Push Button Start Switch, Off-Road Switch Panel, Dash Mount

50337 – 6 Toggle, Push Button Start Switch,  Off-Road Switch Panel, Roll Bar Mount

 

You may also like…

10 Circuit Race Only Chassis Harness/Switch Panel Kit Part No 50005

$519.99

This 10 circuit Race only harness features a relay for each fused circuit and 6 switch contour rocker panel to control it. The wires are pneumatically terminated and pre-inserted into the fuse block and relay blocks. The fuse block is labeled for the circuits below but can be used to power any 12 volt electrical component. The Switch panel measures 8 inches wide X 3 inches tall.  The panel is painted black and silkscreened for easy identification of switch functions.  This panel can be roll bar or dash mounted. Each wire is oversized and custom printed with the circuit identification as well as using GM color codes for easy installation.

Panel Dimensions: 8.25″ L x 3.25″ W x 3″ H

Painless Part Number: 50005 Categories: , Product ID: 20992

Description

This 10 circuit Race only harness features a relay for each fused circuit and 6 switch contour rocker panel to control it. The wires are pneumatically terminated and pre-inserted into the fuse block and relay blocks. The fuse block is labeled for the circuits below but can be used to power any 12 volt electrical component. The Switch panel measures 8 inches wide X 3 inches tall.  The panel is painted black and silkscreened for easy identification of switch functions.  This panel can be roll bar or dash mounted. Each wire is oversized and custom printed with the circuit identification as well as using GM color codes for easy installation.

Panel Dimensions: 8.25″ L x 3.25″ W x 3″ H

You may also like…

21 Circuit Pro Street Chassis Harness w/Switch Panel – Part No 50003

$549.99

If you are looking for a switch panel and harness to keep your racecar streetable, this 21 circuit harness and switch panel combo is for you. As with all of our chassis harnesses this kit has all the wires labeled and is pre terminated at the fuse block for easy installation. This harness includes an optional connector if you want to use a GM column mounted ignition switch. The included switch panel is a roll bar mount 8 switch rocker panel. This panel is prewired and is a direct plug and play into this harness. Also Included is a painless mounting plate, grommets, terminal assortment kit, and the necessary connectors for your turn signal switch, headlights, and alternator. Each wire is custom printed with the circuit identification as well as using GM color codes for easy installation.

Panel Dimensions: 10.75″ L x 3.25″ W x 3″ H

The switch panel is prelabed for the following:

Start
Ignition
Electric Fan
Fuel Pump #1
Fuel Pump #2 / Accessory
Water Pump
Lights
Accessory

Painless Part Number: 50003 Categories: , Product ID: 20989

Description

If you are looking for a switch panel and harness to keep your racecar streetable, this 21 circuit harness and switch panel combo is for you. As with all of our chassis harnesses this kit has all the wires labeled and is pre terminated at the fuse block for easy installation. This harness includes an optional connector if you want to use a GM column mounted ignition switch. The included switch panel is a roll bar mount 8 switch rocker panel. This panel is prewired and is a direct plug and play into this harness. Also Included is a painless mounting plate, grommets, terminal assortment kit, and the necessary connectors for your turn signal switch, headlights, and alternator. Each wire is custom printed with the circuit identification as well as using GM color codes for easy installation.

Panel Dimensions: 10.75″ L x 3.25″ W x 3″ H

The switch panel is prelabed for the following:

Start
Ignition
Electric Fan
Fuel Pump #1
Fuel Pump #2 / Accessory
Water Pump
Lights
Accessory

You may also like…

21 Circuit Pro Street Harness Kit Part No 50002

$324.99

If you want to keep your race car streetable and want to use all of your factory switches instead of a switch panel, this 21 circuit harness is for you. As with all of our chassis harnesses this kit has all the wires labeled and is pre terminated at the fuse block for easy installation. This harness includes an optional connector if you want to use a GM column mounted ignition switch. Also Included is a terminal assortment kit, with the necessary connectors for your turn signal switch, headlights, and alternator. Each wire is custom printed with the circuit identification as well as using GM color codes for easy installation.

Painless Part Number: 50002 Category: Product ID: 20986

Description

If you want to keep your race car streetable and want to use all of your factory switches instead of a switch panel, this 21 circuit harness is for you. As with all of our chassis harnesses this kit has all the wires labeled and is pre terminated at the fuse block for easy installation. This harness includes an optional connector if you want to use a GM column mounted ignition switch. Also Included is a terminal assortment kit, with the necessary connectors for your turn signal switch, headlights, and alternator. Each wire is custom printed with the circuit identification as well as using GM color codes for easy installation.

You may also like…

10 Circuit Race Only Chassis Harness – Part No 50001

$324.99

This 10 circuit Race only harness features a relay for each fused circuit.  The wires are pneumatically terminated and pre-inserted into the fuse block and relay blocks. The fuse block is labeled for the circuits below but can be used to power any 12 volt electrical component. If you are also looking for a switch panel we offer the two switch panels below that are designed to be plug and play and will plug directly into this harness. Each wire is oversized and custom printed with the circuit identification as well as using GM color codes for easy installation.

This harness is designed to be used with our 50201 and 50202 non-fused switch panels but can also be used with any custom fabricated switch panel.

Painless Part Number: 50001 Category: Product ID: 20984

Description

This 10 circuit Race only harness features a relay for each fused circuit.  The wires are pneumatically terminated and pre-inserted into the fuse block and relay blocks. The fuse block is labeled for the circuits below but can be used to power any 12 volt electrical component. If you are also looking for a switch panel we offer the two switch panels below that are designed to be plug and play and will plug directly into this harness. Each wire is oversized and custom printed with the circuit identification as well as using GM color codes for easy installation.

This harness is designed to be used with our 50201 and 50202 non-fused switch panels but can also be used with any custom fabricated switch panel.

You may also like…

Ford 3G Alternator Harness Part No 30831

$78.99

This kit contains all of the components needed in order to connect a Ford 3G Alternator. This kit will contain the following:

  • (1) 7’ Red 6 gauge charge wire
  • (1) 8’ Black/Red ground wire
  • (2) Pre-installed connectors (a 3 pin connector and 1 pin connector)
  • (1) Bag kit containing (150 amp in-line fuse, 1 fuse holder, 2 screws, 6 large un-insulated ring terminals, 4 smaller insulated ring terminals, 4 splices, 4 pieces of heat shrink & 15 zip ties)

Year: Universal
Make: Universal
Model: Universal
Engine: Any
Trans.: Any

Painless Part Number: 30831 Category: Product ID: 20926

Description

This kit contains all of the components needed in order to connect a Ford 3G Alternator. This kit will contain the following:

  • (1) 7’ Red 6 gauge charge wire
  • (1) 8’ Black/Red ground wire
  • (2) Pre-installed connectors (a 3 pin connector and 1 pin connector)
  • (1) Bag kit containing (150 amp in-line fuse, 1 fuse holder, 2 screws, 6 large un-insulated ring terminals, 4 smaller insulated ring terminals, 4 splices, 4 pieces of heat shrink & 15 zip ties)

The popular Ford 3G Alternator conversion just got easier. The Painless 3G kit takes the parts chase away from this ever growing charging system upgrade. Until now, pigtails, large gauge charge wire, and a heavy duty inline fuse have all had to be sourced individually. This kit comes with both alternator connectors pre-installed, 8’ of large 6 gauge charge wire, a weather-proof fuse holder with a heavy duty 150 amp inline fuse, detailed instructions, and all weatherproof splices & ring terminals needed for a proper install.

You may also like…

Jeep Duraspark II Harness Part No 30819

$98.99

Year: UNIVERSAL
Make: JEEP
Model: CJ
Engine: 6/8 Cylinder Jeep CJ Engines
Trans.: Any

Painless Part Number: 30819 Category: Product ID: 20916

Description

Perfect replacement for your Jeep Duraspark II ignition system. It allows for the factory location of your module and coil. This part is recommended if you are also replacing the chassis harness.

Fits 6 and 8 cylinder Jeeps

You may also like…

DuraSpark II Ignition Harness Part No 30812

$85.99

Year: Universal
Make: Universal
Model: Universal
Engine: Carbureted
Trans.: Any

Painless Part Number: 30812 Category: Product ID: 20902

Description

Perfect replacement for your Ford Duraspark II ignition system or to upgrade your old points style ignition. It allows for the factory location of your module and coil. This part is recommended if you are also replacing the chassis harness.

Fits factory Ford Duraspark II Ignition systems with the blue module.

You may also like…

GM Suburban Socket Pigtail Kit (Dual Square Headlights) (88-91) Part No 30353

$99.99

Easily paired with our p/n 20205 Direct Fit Square Body Harness, these socket kits give you all the terminals and connectors you need to wire your exterior lighting on your 1988-1991 Dual Square Suburban front end.

Painless Part Number: 30353 Category: Product ID: 20868

Description

Easily paired with our p/n 20205 Direct Fit Square Body Harness, these socket kits give you all the terminals and connectors you need to wire your exterior lighting on your 1988-1991 Dual Square Suburban front end.

GM Pickup Socket Pigtail Kit (Single Square Headlights) (80-87) Part No 30351

$64.95

Easily paired with our p/n 20205 Direct Fit Square Body Harness, these socket kits give you all the terminals and connectors you need to wire your exterior lighting on your 1980-1987 single square headlight GM Pickup.

Painless Part Number: 30351 Category: Product ID: 20864

Description

Easily paired with our p/n 20205 Direct Fit Square Body Harness, these socket kits give you all the terminals and connectors you need to wire your exterior lighting on your 1980-1987 single square headlight GM Pickup.

27 Circuit Classic-Plus Customizable 1973-1987 GM Truck Chassis Harness Part No 20205

$643.99

This 27 circuit 1973-1987 GMC/Chevy Painless wiring harness was designed to fit the trucks, Blazers, and Suburbans*, whether C10, C20, or C30. It features a factory style bulkhead connector, allowing for easy mounting of the fuse block in the factory location, and has many of the factory connectors already installed on the harness out of the box. Including connectors for: the headlight switch, dimmer switch, wiper motor, ignition switch, blower motor & switch, blower resistor, and instrument cluster. Each wire is custom printed with the circuit identification as well as using GM color codes for easy installation.  Wire your Squarebody once and wire it right with Painless!

This harness does not support factory installed TBI fuel injection or computer controlled carburetors.

* Doesn’t support rear power glass, rear defrost, or rear A/C/Heat – many of these items are separate from the OE chassis harness.

Painless Part Number: 20205 Category: Product ID: 20777

Description

This 27 circuit 1973-1987 GMC/Chevy Painless wiring harness was designed to fit the trucks, Blazers, and Suburbans*, whether C10, C20, or C30. It features a factory style bulkhead connector, allowing for easy mounting of the fuse block in the factory location, and has many of the factory connectors already installed on the harness out of the box. Including connectors for: the headlight switch, dimmer switch, wiper motor, ignition switch, blower motor & switch, blower resistor, and instrument cluster. Each wire is custom printed with the circuit identification as well as using GM color codes for easy installation.  Wire your Squarebody once and wire it right with Painless!

This harness does not support factory installed TBI fuel injection or computer controlled carburetors.

* Doesn’t support rear power glass, rear defrost, or rear A/C/Heat – many of these items are separate from the OE chassis harness.

Factory Style bulkhead connector mounts directly in the original location – no modification to firewall is needed!

Most of the connectors come pre-terminated, making for a painless install!

High amperage charge wire is included allowing you to easily run modern alternators.  The included Midi fuse protects the system, getting rid of the troublesome fusible links that can leave you stranded with no easy fix!

Dual fuel tank ready!  If your Squarebody is a dual tank truck, simply use our included dual tank wiring harness to keep both fuel tanks functioning like the factory intended.

For the few non-preterminated connections, mastic heatshrink is included.  This will allow you to make professional and waterproof connections with a clean appearance!

Due to different front end configurations and bed lengths, this harness comes with open ended headlight and taillight wiring with extra length and can be paired with our light socket kits:30350 – GM Pickup Socket Pigtail Kit (Single Round Headlights) (73-80)

30351 – GM Pickup Socket Pigtail Kit (Single Square Headlights) (80-87)

30352 – GM Pickup Socket Pigtail Kit (Dual Square Headlights) (80-87)

30353 – GM Suburban Socket Pigtail Kit (Dual Square Headlights) (88-91)

You may also like…

26 Circuit Direct Fit 1969 Camaro Harness Part No 20202

$1,116.99

Your most complete ’69 Chevy Camaro Harness! Featuring 26 circuits with virtually every connector installed on the harness out of the box. This harness covers all common options and even features a fully integrated ground circuit.  Included are provisions for the RS headlights and taillights, cowl hood, and even a complete console harness!  Also included is our 120+ page manual full of color schematics, photos, and step-by-step instructions that make wiring your 1969 Camaro a breeze!

Painless Part Number: 20202 Category: Tags: , , , , Product ID: 20775

Description

Your most complete ’69 Chevy Camaro Harness! Featuring 26 circuits with virtually every connector installed on the harness out of the box. This harness covers all common options and even features a fully integrated ground circuit.  Included are provisions for the RS headlights and taillights, cowl hood, and even a complete console harness!  Also included is our 120+ page manual full of color schematics, photos, and step-by-step instructions that make wiring your 1969 Camaro a breeze!

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 150 amp MIDI fuse
  • Fully integrated ground circuit
  • 120+ page manual full of color schematics, photos, and step-by-step instructions

The heart of your new Camaro wiring harness is centered around this factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Also included are pre-terminated connectors for either standard or RS taillight options.  Don’t have RS taillights now but may add them down the road?  Simply unplug the new connector and plug in the new one!

The new status indicator circuit boards replace the brittle factory indicator light molded plastic and provide color correct incandescent bulbs to retain the factory look. Ever need to replace a bulb down the road?  The board are easily unplugged and removed and bulb changes are a breeze!

Each pre-terminated connector is tagged for easy routing and installation.

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!

You may also like…

26 Circuit Direct Fit 1970-72 Chevelle / Malibu Harness Part No 20130

$1,088.99

This direct fit wiring harness gives you everything you need, plus more to wire your 1970, 1971, or 1972 Chevelle! Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Various pigtails & light sockets are provided, so the harness easily fits mismatched cars (1971-1972 cars with 1970 front ends, or 1970 cars with 1971-1972 rear bumpers). The gauge cluster pigtail provided allows for the square “full sweep dash” harness and includes a “Super Sport” cluster pigtail. This makes it easy for those with a “full sweep” dash to swap to a “SS” style cluster at a later date by only undoing one connector and plugging in the separate pigtail on the harness. This harness follows all of the same wire routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 140+ page manual full of color schematics, photos, and step-by-step instructions!

Painless Part Number: 20130 Category: Product ID: 20773

Description

This direct fit wiring harness gives you everything you need, plus more to wire your 1970, 1971, or 1972 Chevelle! Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Various pigtails & light sockets are provided, so the harness easily fits mismatched cars (1971-1972 cars with 1970 front ends, or 1970 cars with 1971-1972 rear bumpers). The gauge cluster pigtail provided allows for the square “full sweep dash” harness and includes a “Super Sport” cluster pigtail. This makes it easy for those with a “full sweep” dash to swap to a “SS” style cluster at a later date by only undoing one connector and plugging in the separate pigtail on the harness. This harness follows all of the same wire routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 140+ page manual full of color schematics, photos, and step-by-step instructions!

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 100 amp MIDI fuse
  • Fully integrated ground circuit
  • 140+ page manual full of color schematics, photos, and step-by-step instructions

Note: Options not supported in these harnesses are: the TCS relay, convertible top, rear defrost, wiring for the factory power window/locks, and factory A/C wiring. These harnesses do include the switch power wire for the factory power window/locks and A/C. These harnesses do include a new blower motor harness for those with heat only systems.

The heart of your new Chevelle wiring harness is centered around this factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Don’t have a center console but may add one later?  The included console harness can be easily added at any time.

Each pre-terminated connector is tagged for easy routing and installation.

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!

You may also like…

26 Circuit Direct Fit 1969 Chevelle / Malibu Harness Part No 20129

$1,028.99

This direct fit wiring harness gives you everything you need, plus more to wire your 1969 Chevelle!  Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Including options like a console sub-harness, two gauge cluster pigtails, and even a fully integrated ground circuit. This harness follows all of the same wire routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 120+ page manual full of color schematics, photos, and step-by-step instructions!

Painless Part Number: 20129 Category: Product ID: 20771

Description

This direct fit wiring harness gives you everything you need, plus more to wire your 1969 Chevelle!  Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Including options like a console sub-harness, two gauge cluster pigtails, and even a fully integrated ground circuit. This harness follows all of the same wire routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 120+ page manual full of color schematics, photos, and step-by-step instructions!

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 150 amp MIDI fuse
  • Fully integrated ground circuit
  • 120+ page manual full of color schematics, photos, and step-by-step instructions

Note: Options not supported in these harnesses are:  wiring for the TCS relay for turbo 400 transmissions, wiring for the factory power window/locks, and factory A/C wiring. These harnesses do include the switch power wire for the factory power window/locks and A/C. These harnesses do include a new blower motor harness for those with heat only systems.

The heart of your new Chevelle wiring harness is centered around this factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Don’t have a center console but may add one later?  The included console harness can be easily added at any time.

Each pre-terminated connector is tagged for easy routing and installation.

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!

You may also like…

26 Circuit Direct Fit 1968 Chevelle / Malibu Harness Part No 20128

$1,009.99

This direct fit wiring harness gives you everything you need, plus more to wire your 1968 Chevelle! Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Including options like a console sub-harness, two gauge cluster pigtails, and even a fully integrated ground circuit. This harness follows all of the same wire routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 120+ page manual full of color schematics, photos, and step-by-step instructions!

Painless Part Number: 20128 Category: Product ID: 20769

Description

This direct fit wiring harness gives you everything you need, plus more to wire your 1968 Chevelle! Not only are there provisions for connecting standard factory components, we also provide what you will need for aftermarket components. Including options like a console sub-harness, two gauge cluster pigtails, and even a fully integrated ground circuit. This harness follows all of the same wire routing found on the factory harness which allows you to utilize the factory harness attachment points. Extra length has even been added to the headlight section to be routed behind the driver side inner fender for a cleaner look. Also available is a 120+ page manual full of color schematics, photos, and step-by-step instructions!

  • Numerous components have the connectors and terminals pre-installed to make connections plug-n-play
  • All exterior lights have the correct sockets and bulbs pre-installed
  • 6 gauge charge wire and 150 amp MIDI fuse
  • Fully integrated ground circuit
  • 120+ page manual full of color schematics, photos, and step-by-step instructions

Note: Options not supported in these harnesses are: wiring for the TCS relay for turbo 400 transmissions, wiring for the factory power window/locks, and factory A/C wiring. These harnesses do include the switch power wire for the factory power window/locks and A/C. These harnesses do include a new blower motor harness for those with heat only systems.

The heart of your new Chevelle wiring harness is centered around a factory style precision molded fuse block.  Updated ATC style fuses ensure that the 26 circuits stay protected and safe.

The backside of the fuse block utilizes a factory style bulkhead connector to ensure there is no trimming or cutting to your firewall.  This allows you to easily install the fuse block in the factory location.

Plug and play design makes install easy, no matter your options.  Don’t have a center console but may add one later?  The included console harness can be easily added at any time.

Each pre-terminated connector is tagged for easy routing and installation.

There is no need to make extra trips to the parts store with this kit.  Connectors, terminals, extra fuses, light bulbs, etc., all come in the box.  Any questions while installing?  Just refer to the complete 120+ page installation manual, or give our tech line a call!

You may also like…

22 Circuit Direct Fit 1969-70 Mustang Chassis Harness Part No 20122

$849.99

This harness includes circuits for:

  1. A/C & Heat
  2. Accessory / Cigarette Lighter
  3. Accessory Relay
  4. Backup Lights
  5. Brake Lights
  6. Charging
  7. Courtesy and Dome Lights
  8. Electric Choke
  9. Emergency Flashers
  10. Fused Power Source
  11. Glove Box Light
  12. Headlights
  13. Horn (Relay)
  14. Ignition Coil
  15. Instrument Panel Lighting and Gauges*
  16. Park Lights
  17. Radio/Clock (Constant and Switched)
  18. Starting
  19. Tail Lights and License Plate Light
  20. Trunk Light
  21. Turn Signals
  22. Wipers and Washer Pump

* Including Wires For:
Aftermarket Tachometer
Ammeter
Brake Warning Light
Fuel Gauge
Gear Indicator Light
Oil Gauge
Tachometer
Temperature Gauge
Voltmeter

Number of Circuits: 22 Circuits – 12 Fuses w/ Horn Relay, Accessory Relay and Maxi Fuse
Harness Length: Factory Fitment
Fuse Type: Mini Blade & Maxi Fuse
Firewall Passthrough: Grommet
Color Code Based:  Factory Ford
Circuit Designations: Printed on Wires

Complete Ford color-coded chassis wiring harness for:

  • 1969 Ford Mustang
  • 1970 Ford Mustang
Painless Part Number: 20122 Category: Product ID: 20767

Description

This 22 circuit direct fit 1969-1970 Ford Mustang wiring harness has many of the factory connectors already installed on the harness out of the box.  This harness uses our unique covered micro-fuse block.  Also featured is an auxiliary circuit with 20 amp relay for accessories such as fog lights, or an electric fuel pump. Each wire is custom printed with the circuit identification as well as using Ford wiring color codes for easy installation.

Fits:

  • 1969 Ford Mustang
  • 1970 Ford Mustang

You may also like…

22 Circuit Direct Fit 1967-68 Mustang Chassis Harness – Part No 20121

$779.99

This direct-fit harness includes circuits for:

  1. A/C & Heat
  2. Accessory / Cigarette Lighter
  3. Accessory Relay
  4. Backup Lights
  5. Brake Lights
  6. Charging
  7. Courtesy and Dome Lights
  8. Electric Choke
  9. Emergency Flashers
  10. Fused Power Source
  11. Glove Box Light
  12. Headlights
  13. Horn (Relay)
  14. Ignition Coil
  15. Instrument Panel Lighting and Gauges*
  16. Park Lights
  17. Radio/Clock (Constant and Switched)
  18. Starting
  19. Tail Lights and License Plate Light
  20. Trunk Light
  21. Turn Signals
  22. Wipers and Washer Pump

* Including Wires For:
Aftermarket Tachometer
Ammeter
Brake Warning Light
Fuel Gauge
Oil Gauge
Tachometer
Temperature Gauge
Voltmeter

Number of Circuits: 22 Circuits – 12 Fuses w/ Horn Relay, Accessory Relay and Maxi Fuse
Harness Length: Factory Fitment
Fuse Type: Mini Blade & Maxi Fuse
Firewall Passthrough: Grommet
Color Code Based:  Factory Ford
Circuit Designations: Printed on Wires

Complete Ford color-coded chassis wiring harness for:

  • 1967 Ford Mustang
  • 1968 Ford Mustang
Painless Part Number: 20121 Category: Product ID: 20765

Description

This 22 circuit direct fit 1967-1968 Ford Mustang wiring harness has many of the factory connectors already installed on the harness out of the box.  This harness uses our unique covered micro-fuse block.  Also featured is an auxiliary circuit with 20 amp relay for accessories such as fog lights, or an electric fuel pump. Each wire is custom printed with the circuit identification as well as using Ford wiring color codes for easy installation.

Fits:

  • 1967 Ford Mustang
  • 1968 Ford Mustang

You may also like…